12/26/2009

VCP-410 Dumps

QUESTION NO: 322
An administrator is using Guided Consolidation and has added a system for
Analysis. After 30 minutes, the status has not changed from Collecting System
Information to Analyzing. Which of the following statements indicates why this might
occur?
A. The status change should be immediate and the Guided Consolidation Service status
should be checked on Passed VCP410 the vCenter Server
B. Guided Consolidation can take up to 24 hours to collect system information before the
status changes to Analyzing
C. Guided Consolidation can take up to 8 hours to collect system information before the
status changes to Analyzing
D. Guided Consolidation can take up to 1 hour to collect system information before the
status changes to Analyzing

Answer: D

QUESTION NO: 323
When using the Explicit Failover option for a virtual switch with multiple
uplinks, ESX determines the uplink to use in a failover event by?
A. using link state tracking to see which uplinks are connected
B. using beacon probing to Passed VCP 4 discover which uplink has the shortest route
C. a specified list
D. using the reported uptime to determine which uplink to select

Answer: C

QUESTION NO: 324
Which of the following vSphere features cannot be used with virtual
machines that are enabled for VMware Fault Tolerance (Choose Two)?
A. RDMs in Virtual Compatibility Mode
B. VMware SMP
C. VMware EVC
D. VMware DRS

Answer: B,D

QUESTION NO: 319
What is the size of a Virtual Machine .vswp file if defaults are taken for the
VM reservations, limits, and shares?
A. The VM .vswp file is equal to the amount of virtual memory (VM available memory
plus VM overhead)
configured for the VM when it was created
B. The VM .vswp file is set to zero length when the VM is created and grows as
necessary
C. The VM .vswp file is equal to twice the amount of available memory configured for
the VM when it was created
D. The VM .vswp file is equal to the amount of available memory configured for the VM
when it was created

Answer: D

QUESTION NO: 320
The maximum number of vcp 410 hosts in a VMware HA cluster is?
A. 8
B. 32
C. 24
D. 16

Answer: B

QUESTION NO: 321
Which of the following is the technology used by VMware Fault Tolerance?
A. VMware vSafe
B. VMware vCluster
C. VMware vShield
D. VMware vLockstep

Answer: D

Dec 26, 2009 12:14:59 PM

The comments to this entry are closed.

NEXT POST
Testking VCP-410 Appendix A – ESX Technical Support Commands Command Purpose esxcfg-advcfg advanced options esxcfg-auth Configures authentication esxcfg-boot bootstrap settings esxcfg-dumppart Configures a diagnostic partition esxcfg-firewall service console firewall ports esxcfg-info Information VCP-410 questions about the state of the service console, VMkernel, various subsystems in the virtual network, and storage resource hardware. esxcfg-init Internal initialization routines. Used for the bootstrap process you should not use it under any circumstances. esxcfg-module Sets driver parameters and modifies which drivers are loaded during startup. esxcfg-mpath multipath settings for your Fibre Channel or iSCSI disks. esxcfg-nas Manages NFS mounts esxcfg-nics physical network adapters esxcfg-resgrp resource group...
PREVIOUS POST
VCP-410 Test Questions o On ESXi, it is not possible to rescan a single storage adapter. o You can modify the Disk.MaxLUN parameter to improve LUN discovery speed. o You cannot discover LUNs with a LUN ID number that is greater than 255. o You can disable the default sparse LUN support to decrease the time ESX/ESXi needs to scan for LUNs. o The sparse LUN support enables the VMkernel to perform uninterrupted LUN scanning when a storage system presents LUNs with nonsequential LUN numbering. o NPIV enables a single FC HBA port vcp-410 to register several unique WWNs with the fabric, each...